Corsair 970 Carbon-XL

Mechanical equipment

Exterior / Laminate
Finish: Hulls and decks molded female, external gelcoat finish
Hull laminate: Hull laminate formed under vacuum. Eglass laminate with extensive use of carbon fiber for structural reinforcement.
Hull core material: Closed-cell PVC foam core
Deck laminate: Deck laminate formed under vacuum. Eglass laminate with extensive use of carbon fiber for structural reinforcement.
Deck core material: Closed-cell PVC foam core
General laminate: Polyester resin laminate formed under vacuum
General core material: Closed-cell PVC foam core

Galley equipment

Interiors
Glossy gelcoat finish for furniture and cabin sides
Floors: lightweight synthetic wood
Spacious kitchen with storage space under the counter
Berths 5/6 (2 in the forward cabin, 2 in the aft cabin, 1/2 in the enlarged main bed mid-hull*,)
Internal walls covered in carpet in the forward and aft cabins
Removable wooden dining table with adjustable Lagun mounting system (for cabin and cockpit)
Additional shelves behind the sofas, next to the sink, to the left of the fin case, to enhance storage (*)
Large chart table with storage compartments (*)
Manual Jabsco toilet, sink and mirror with pull-out shower in the molded area, with privacy door Freshwater pressurized in the kitchen, bathroom/shower, and aft shower areas
Large stainless steel sink
Pressurized seawater/lake water in the kitchen and on deck; serves as an additional bilge pump if necessary (*)
Freshwater tank capacity 150 lt
Waste tank capacity 40 lt with discharge pump on deck
Vitrifrigo L41 refrigerator/freezer (*)
Two-burner propane stove, stainless steel pot supports, with safety device for flame failure
Manual bilge pump (deck) and automatic electric bilge pump Whale Supersub Smart (*)
Electric shower bilge pump
Fittings through the hull in Marelon compliant with CE/ISO standards

Deck and hull equipment

Trees and Sails
Carbon mast Axxon Racing Rotating Wing, 14.6mt/48ft, 1 set of stays, Antal 22mm track with gate (*)
Dyneema Colligo stays and end fittings (*)
White LED bow light and strong Dr. LED white/red lights for the stays
7mm stainless steel mast head (*)
Structural furler Jiber JB15RW Ubi Maior with continuous line ratchet drum; this is also a reduction furler (*)
Continuous line furler Karver KF1 and joint for Screecher (*)
Continuous line furler Karver KF2 and joint for Code Zero (*)
Facnor Thimble top-down Fast 2500 for Code Zero (*)
All control line circuits of the furler include tensioners under the deck
2 Antal brakes for the sheets of the Screecher and Code Zero 2:1
Armare Ropes: Main 2:1; Genoa 1:1; Screecher 2:1; Code Zero 2:1 (*)
2 remote control cable clamps Cousin Constrictor (Main and Genoa)(*)
Carbon Axxon boom, extended length, with 6 Spinlock XCS 0610 brakes for reduction (*)
3 double sets of reduction lines 2:1 (*)
All sail movement controlled from the cabin, including raising and lowering sails, rolling, main reduction and Cunningham, mast rotation (*)
Retractable carbon bowsprit
Equipment for raising/lowering the mast: mini-stays, mast raising pole+yoke+central support wheel (*2021), mast supports aft+forward
The original 12mt aluminum rotating mast with rotating boom is available upon request
 
Sail Inventory (all 2017)
Squaretop Main, North Sails 3Di Race 14,700Dpi, full-length battens, 3 reductions, 49 sqm (*)
Genoa, North Sails 3Di Endurance 16,800 Dpi, roller, with 3 vertical battens, 22.4 sqm, designed with roller reduction capability (*)
Screecher, North Sails 3Di Endurance 12,600Dpi, roller, 49.6 sqm (*)
CodeZero (Asymmetric 75% smg), North Sails NLP Sport Xi06, top roller, 78 sqm (*)
Sail/bag cover with 2 full-length battens; cover for rolled main boom (for transport) (*)
Sail sheets from Armare Ropes (*)
 
Deck
1 Lewmar 44 hatch at the bow; 2 Lewmar 10 hatches on the cabin roof; 1 Lewmar 70 hatch at the stern; 2 x Lewmar 30 floating hatches; 3 x Lewmar opening portholes at the stern;
Side cabin windows in darkened polycarbonate and washboards for the passage
Storage compartments in the cabin; molded compartment for safety equipment in the cockpit
Stainless steel helm seats at the stern
Stainless steel bow wings (for anchor roller and bow net ties)(*)
Gray floating nets and rear nets coated in PVC; enlarged bow nets in Dyneema (multihull nets, FL)(*)
6 Winches: 4 Harken Perfoma (2 40.2 ST, 2 40.2 with Barton Wincher), 2 Pontos Compact ST, 2 winch handles(*)
Harken traveler track 2.5mt, on carbon structure at the stern, with Harken Windward Sheeting traveler car and 4:1 control lines, on 2 Spinlock PXR sheets (*)
Harken 6:1 main sheet locking system, with fine adjustment 30:1, on two Spinlock PXR sheets (*)
2 Lewmar 10mm rope brakes (Screecher and CZ sheets)
7 Spinlock PXR sheets and 8 Harken cam cleat sheets
2 pulleys for Screecher/Code-zero sheets
2 double deck organizers Schaefer
High aspect ratio composite daggerboard and retractable rudder
Wooden tiller with Spinlock EA tiller extension (*)
Ronstan Battlestick tiller extension (*)
Aluminum A80 Spade anchor, Mantus S1 joint, 20mt 8mm chain with 100mt ½” Yale Brait line (*)
Anchor box with Italwinch Smart Plus 12V winch with remote control (*)
Boat lifting eyes, with 4 dyneema lifting straps(*)
Floating and removable swim ladder at the stern
20 sqm tent

Navigation systems

Instruments and Electronics
Electrical system with 16-position switch panel
Marine-grade tinned copper electrical wires
LED navigation lighting with strong diffuser (red/white) and bow lights;
Red/white LED lights in the forward, main, and aft cabins;
7 12V sockets and 3 220V sockets(*)
CE approved navigation lights
Anchor light/navigation lights at the masthead
Raymarine transducers for speed, wind, depth, and compass, with two displays
Wall-mounted Ritchie compass
Solar-powered wind instrument OpenWind for rotating mast (*)
Raymarine AIS 350 receiver (*)
Raymarine autopilot with ACU-100 actuator, EV-1 sensor, S1 drive, P7 display, and S100 wireless remote (*)
Lowrance Link 5 VHF, with mast-mounted antenna
Li-ion 100Ah and AGM 75Ah batteries with 2 wireless battery monitors (*)
Xantrex XC5012 50amps 3-bank charger (*)
Solbian AIO 47SP 47W solar panel with controller (*)

Additional equipment

Drift plate (remotely controlled from the bridge)
Pivoting rudder (180°)
Lightweight aluminum folding system, key for removing/tightening the locking bolts
2015 Honda BFD-20 XRTU outboard motor, 20hp, extra-long shaft, electric tilt, 12A charger (*)
Rudder-outboard connection remotely controlled for outboard steering (*)
Spinlock ATCU remote outboard control unit and 17-foot Teleflex cables (*)
10lt fuel tank
International Paint Ultra 300 antifouling paint
3D Marine Twin Air 250 Tender with Honda BF2.3D6 SCHU Outboard Motor
4 mooring lines and 3 fenders
Harbeck BT 3000 aluminum trailer, dual axle, with two spare wheels and tie-down straps, inspection 9/2023 (*)
Flag and registration: Poland